Volume Booster

Fix the level of a quiet voice memo, a soft rehearsal recording or a song that is too loud for your video. Raise or lower the volume by up to 20 dB, or normalize so the loudest moment sits just below the maximum – without crunchy distortion.

  • Files stay on your device
  • Free, no sign-up
  • Instant
Drop an audio file here MP3, WAV, M4A, OGG, FLAC or WebM

Processed on your device. Your files are not uploaded to any server.

Quick guide · 4 steps

How to use the Volume Booster

When to use the Volume Booster

Quiet phone recordings

Bring up a rehearsal, lesson or interview recorded from across the room.

Matching tracks in a playlist or video

Raise or lower one song so it sits at the same level as the others.

Music under a voice-over

Lower a background track by 10–15 dB before adding it to a video.

Preparing files for upload

Normalize finished tracks so they are not much quieter than other songs.

Features and benefits

  • Volume change from −20 dB to +20 dB in half-decibel steps
  • One-click normalize to −1 dBFS
  • Peak meter that shows how much headroom the file has
  • Distortion protection that stops the boost before clipping

Example

Input
rehearsal.m4a – peak −14.2 dBFS, hard to hear
Output
rehearsal.mp3 – normalized, peak −1.0 dBFS

How the Volume Booster works

The tool first scans every sample to find the peak level and shows it in dBFS. A change in decibels is converted to a multiplier – plus 6 dB is about ×2 – and every sample is multiplied by it. With distortion protection on, the multiplier is capped so the loudest sample cannot exceed full scale. Normalize calculates the exact multiplier that takes the current peak to −1 dBFS. Because the same multiplier is applied everywhere, the shape of the recording and the balance between loud and soft passages stay exactly as they were.

A real-life example

Sana recorded her daughter’s piano recital on a phone at the back of the hall, and the file was barely audible. The peak meter showed −15 dBFS, so she chose Normalize. The whole recording rose by 14 dB, the music became clear at normal volume, and the loud final chord stayed clean.

Good to know

Decibels describe changes in level. Plus 6 dB roughly doubles the signal’s amplitude and sounds noticeably louder; minus 6 dB roughly halves it. Digital audio has a hard ceiling called 0 dBFS (decibels relative to full scale). Push a peak past it and the waveform is chopped flat, which sounds like crackling. That is why the tool shows the current peak before you start.

Normalizing is the quickest fix for recordings made with the microphone too far away or the input gain too low. The whole file is raised by one fixed amount until its loudest point reaches −1 dBFS, so the balance between quiet and loud passages is preserved exactly. Setting a custom change is better when you want two files to match, or when a song needs to sit lower under a voice-over.

This tool changes overall level, not loudness over time. If a recording has one very loud moment and is otherwise quiet, normalizing will be limited by that moment; cut it out first with the Audio Cutter. Background hiss rises along with the voice, so start from the cleanest recording you have.

Tips for the best results

  1. Use Normalize first; switch to a custom change only if you need a specific level.
  2. Lower music by 10–15 dB when it will play under speech.
  3. Cut out one-off loud bangs before normalizing so the rest can be louder.
  4. Save as WAV if you will process the file again.
  5. Compare with the original at the same playback volume before deciding.

Common mistakes to avoid

Turning off protection and boosting a lot

Clipped peaks crackle and cannot be repaired later. Keep protection on.

Expecting the tool to remove noise

Volume changes affect everything equally, including hiss.

Normalizing every song to 0 dB

Leave −1 dB of headroom so MP3 encoding and players do not distort.

Volume Booster – frequently asked questions

How much louder can I make a file?

Up to +20 dB. With protection on, the boost stops automatically where the loudest sample would distort.

What does normalize do?

It raises or lowers the whole file by one amount so the loudest point reaches −1 dBFS, keeping the dynamics the same.

Will boosting add noise?

It does not add noise, but existing hiss gets louder by the same amount as everything else.

Can I make a file quieter?

Yes. Move the slider below zero – for example −6 dB to roughly halve the level.

Is normalizing the same as compression?

No. Normalizing changes the whole file by one amount; compression reduces the difference between loud and quiet parts.

Can I boost only the bass?

Use the Bass Booster, which raises low frequencies and protects against distortion.